After you build a design, the Data tab will include a test plan with Response columns for entering response data. Each cell in a Response column is used to record the response value obtained at the combination of factor settings (green columns) specified in the current row. Note that robust parameter designs work differently; for more information on using these designs, see Using Robust Parameter Designs.
The columns shown in the test plan will vary depending on the design type you are working with. To hide/show columns, choose Data > Format and View > Visible Columns or click the Visible Columns icon on the control panel.
The available columns are described below.
Standard Order displays the basic order of runs, as specified in the design type, without randomization. This pattern is provided as a reference (e.g., textbook examples often use the standard order).
Tip: If you need to use a non-randomized order in an actual experiment, you can sort the design by clicking a cell in the column you wish to sort by and choosing Sheet > Sheet Actions > Sort > [Order]. For example, if changing levels in a randomized experiment would be too expensive, you can sort the design table by factor levels.
Run Order displays the randomized order generated by the software. By conducting experiments using a randomized order, you can reduce the effect of factors not being investigated.
Point Type indicates what kind of point the run is. 0 indicates that the run is a center point. 1 is used for all other points.
Block Value displays the block to which the run belongs. If the design is not blocked, all rows will display the same default value.
Life Data Columns are present only for reliability DOE. The columns that are available depend on the type of life data specified when the design was created. These columns take the place of the response column(s) in a standard design, and are used to calculate the underlying response for the design, which is considered to be time.
Time Failed Column allows you to enter the failure time for each unit. This column is available only for times-to-failure data with no censoring (complete data).
State F or S Column allows you to specify whether the unit is failed (F) or suspended (S). This column is available only for data with right censoring.
Time to F or S Column allows you to enter the failure time for the unit or, in the case of suspended units, the time at which the unit was removed from the test while still operating. Note that you can enter a negative number in this column and it will automatically be marked as a suspension in the State F or S column. This column is available only for data with right censoring.
Last Inspected Column allows you to enter the last time the unit was inspected prior to the time it failed. This column is available only for data with interval and/or left censoring.
State End Time Column allows you to enter the time at which the unit’s state was discovered (i.e., the first inspection time after the unit’s failure). This column is available only for data with interval and/or left censoring and without right censoring.
To change the type of life data used in the experiment, use the Alter Data Type window.
Factor Columns
display the settings used for each factor in the run. By default,
these columns are titled using the format "X: Factor
Name," where X is the abbreviated name. If you have defined
the units for the factor, that will also be displayed in the
column heading. Factor columns are shown in green by default.
Factor levels can be displayed as the actual values assigned
in the factor properties or as coded values. When you use
coded values for two level factorial or Plackett-Burman designs,
the low level will be displayed as -1 and the high level will
be displayed as 1. When you use coded values for general full
factorial or Taguchi OA factorial designs, the lowest level
will be displayed as 1, the next level as 2, and so on. To
switch between coded and actual values, choose Data
> Display > [Value Type].
Ignore / Include allows you to specify whether the run will be included in the analysis. You can also enter an asterisk (*) in a response column to ignore that data point.
Comments allows you to enter notes or other text for each run. This information is not used in any calculations.
If your design includes only one observation per test run, the following columns may be available:
Response
Columns allow you to enter the response(s) for each
test run. A response column heading will include the response
name and (if specified) units you
have defined on the Design tab.
Each column contains a check box in the column heading that
specifies whether the response will be included in the analysis.
If a column is selected, the color of the check box border
will indicate the status of that response's analysis. A green
border indicates that the response has been analyzed using
the current analysis settings; a red border indicates that
it has not. Note that if you clear the check box, you will
not be able to specify analysis settings for the response,
nor will you be able to display it in plots
or use it in optimization.
Response Standard Deviation Columns are available only when you select to perform variability analysis. These columns are populated by the software when the data set is analyzed, and they show the standard deviation of the selected response at each factor level combination. (Asterisks indicate that the standard deviation was shown in a previous row.)
If your design includes multiple measurements per test run, the following columns will be available:
Repeated Measurements Columns are available if you chose to include repeated measurements under the Additional Settings on the Design tab. The measurements for each test run are used to generate an average and standard deviation value for that run, either of which can be selected as the analyzed response for the experiment.
The Y Mean and Y Standard Deviation Columns are populated by the software when the data set is analyzed. They show the mean and standard deviation of the measurements taken during each test run.