Defining the Life Profile
For any FIDES analysis, you will be able to specify different phases that a system or assembly experiences during operation (i.e., define the item's life profile). Some of the component properties (such as applied voltage or power dissipated) can then be defined separately for different phases. The phases themselves also have various properties that will affect the failure rate calculations (such as ambient temperature and environmental pollution).
This topic describes how to use the Item Phases window, Select Phases window and Select Phase Set window to specify which phases will be used when performing a FIDES analysis for a particular system or assembly. For information about managing the list of all phases and phase sets in the current database, see Manage Database Phases and Manage Phase Sets.
Tip: Any changes to a saved phase record will be applied automatically to every FIDES analysis where that phase is being used. This is different from using saved pi factor assessments, where the change does not take effect until you take a specific action to update the analysis (see Update Factors).
This topic covers the following subjects:
Specifying Different Phases for Different Levels in the System Hierarchy
When the configuration that you have defined in the System Hierarchy panel contains multiple levels, you can either use the same phases for all levels, or you can specify different phases for any particular branch. For example, the following picture shows a simplified configuration in which the FIDES standard item 
represents a system and the blocks 
represent three different subsystems.
Inherit from Parent
If all of the subsystems will experience the same operating phases, you can specify the phases at the top level (the FIDES standard item ) and allow each block to inherit its phases from the parent item.
If the Define At This Level command is enabled, the block is set to use the same phases as the parent item. All of the remaining ribbon commands (Select Phases, Remove Phase, etc.) will be disabled and you will not be able to modify the list of phases that are applicable for the current block. The table will display the same phase information that was defined for the higher level.
Define At This Level
Alternatively, if any of the subsystems will experience different operating phases, you can choose to define the phases for one or more individual blocks.
If the Define At This Level command is disabled, the block is set to use different phases than its parent item. The remaining ribbon commands (Select Phases, Remove Phase, etc.) will be enabled and you will be able to modify the list of phases that will be applicable for the current block.
Changing the Selection
By default, each new block that you create in a FIDES branch of the system hierarchy will be configured to use the same phases as the parent item. To change that, open the Item Phases window and click the Define At This Level command.
If you have defined different phases for a particular block, but you wish to go back to using the same phases as the parent item, click the Inherit from Parent command.
Viewing and Selecting the Item Phases
To access the Item Phases window, select an item in the system hierarchy and then choose Prediction > FIDES > Item Phases.
This command will be enabled only if you have selected a FIDES standard item or a block that belongs to a FIDES standard item. Note that this also includes all of the specialized block types that are used in FIDES analyses (COTS Board and Hybrid/Multi Chip Module).
The Item Phases window displays the phases that will be used in the calculations for all components in the next level below the selected item. If there are any blocks in the next level, you can choose whether their components will inherit the same phases as the parent item, or specify different phases for that branch, as described above.
All of the phases that you use in a FIDES analysis must have been predefined in the list of phases that are saved in the database. If a saved phase is modified at any time, the changes will be applied automatically to any FIDES analysis that uses the phase.
The purpose of the Item Phases window is to:
- Select which of the saved phases or phase sets are applicable.
- Specify "local" titles that reflect how each predefined phase is being used in the analysis for this particular item. This is set in the "Title (for this item)" column and the names must be unique for the item.
- Specify the order in which the phases occur for the particular item.
Note that the local title and the order do not have any effect on the calculations but they will determine how phased component properties are displayed in the Properties panel.
For example, both pictures below show a situation where you can set a different applied voltage for each different operating phase in an aircraft’s mission. The phase labels (Pre-Flight Taxi, Takeoff, etc.) come from the "Title (for this item)" column in the Item Phases window. The "Pre-Flight Taxi" and "Post-Flight Taxi" phases are linked to the exact same saved phase, but they have different local titles to reflect their purpose in the analysis.
The Grouped phase properties option on the Other Settings page of the Application Setup determines how these phase labels are displayed in the Properties panel. The picture on the left shows how the properties are displayed when the option is selected; the picture on the right shows how the properties are displayed when the option is cleared.
The ribbon in the Item Phases window provides the following commands:
Inherit from Parent or 
Define at This Level will be enabled only if you are viewing the phases for a block. You can use them to specify that the block will inherit the same phases as the parent item or that you will specify a different set of phases for that branch, as described above.
Select Phases and 
Select Phase Set allow you to select any of the phases or phase sets that have been saved in the database. If you want to use both, first select the phase set and then append individual phases at the end of the list.
Duplicate Phase creates another instance of the same phase in the list for the current item. This will be convenient if the assembly experiences the same phase more than once in a single mission. For example, an aircraft goes through the taxi phase at both the beginning and the end of a mission.
Remove Phase removes the selected phase from the list for the current item. (Note that the saved phase record will still be available for other FIDES analyses in the current database. If you wish to permanently delete the phase, use the Delete Phase command in the Manage Database Phases window.)
Move Up and 
Move Down move the selected phase up or down in the list. The phase order does not impact the calculations; it simply determines how phased properties are organized in the Properties panel.
Manage Database Phases allows users with the "Manage Lambda Predict database settings" permission to manage all of the phases that have been saved in the database. This will be convenient if you want to assign a new phase that has not yet been defined in the database or if you need to change the properties for any of the saved phases. The command opens the same Manage Database Phases window that is accessible from the FIDES Settings Manager window.
Send to Excel exports the current table to a new Excel spreadsheet.
Show Copy Component Parameters Column: Available starting in Version 2023, toggles the "Copy Component Parameters from Phase" column on/off. This column allows you to copy the component properties that you have specified for any phase that is assigned to the item and use them in another phase assigned to the item. Click inside the cell for the target phase and choose the source phase in the drop-down list that becomes available; the list will include all phases currently assigned to the item, as well as any phases that you have removed from the item in this session. When you close the Item Phases window, the session ends and component properties that were specified for phases you removed will no longer be available for use.